You have no items in your shopping cart.

You have no items to compare.

IMS Bearing Kits

MY06-08 Intermediate Shaft IMS Reseal Kit


More info on LN Engineering's Prop 65 policy

MY06-08 Intermediate Shaft IMS Reseal Kit

$199.00

In stock

SKU: 996-105-024-06-KIT

LN Engineering MY06-08 Intermediate Shaft Flange Reseal Kit including our LN Billet IMS Flange. Direct replacement for factory 06-08 IMS flange. This kit provides you a new IMS flange along with all the required seals and hardware to install the new flange. Don't forget to change your rear main seal while you are in there and always use a Genuine Porsche RMS.


Includes (Qty.) (3) 900 385 093 01 (LN) bolts, (1) 999 707 571 40 18 X 2 mm o-ring for center stud, (1) 996 105 112 01 IMS flange seal, and (1) 999 076 084 01 nut (Genuine Porsche)


With model year 2006 through 2008, a larger IMS bearing was used. However, the IMS flange housing bore diameter was not increased, which prevents replacement of the bearing without complete dis-assembly of the engine. No need to take drastic measures like bore out your engine case to remove the original bearing or install an oil feed. Keep reading to learn more.


The incidence of failure with a 2006-2008 M96 or M97 Engine as found in the Boxster, Cayman, and 911 that have the larger (but non-serviceable) IMS is highly unlikely. We would estimate about a 1% failure rate.However, this bearing can still be problematic.


When you have your clutch replaced, it’s best to have the grease seal removed off the original bearing. Since the IMS is located at the bottom of the engine and is submerged in oil, removing the grease seal will allow engine oil to better lubricate it. There is a black plastic seal on the front of the bearing – you would use a dental pick or something similar to pop the seal out of it’s groove. Just be sure not to drop it into the engine when you do remove it. Here is a short video on YouTube that shows how to remove the grease seal ron a ball bearing:





Note: All IMS Removal procedures must done before the flange is removed. IMS Pro Tool Kit 106-08.13 required. Tool rental is not offered with this product nor technical support for installation. You must follow the factory IMS flange removal and reseal procedure. Free basic technical support is provided through our ticketing system. Assistance with the IMS procedure is not provided outside of directives and videos provided online. Advanced Technical Support (ATS) is a paid service where you can speak to an actual technician experienced with the IMS procedure and your vehicle to assist in case you run into a problem you cannot solve on your own.



Description

Details

Cross reference part numbers 996-105-024-06-KIT; 996 105 024 06 KIT.

Additional

Additional Information

Brand LNE
MPN 996 105 024 06

Important Seller's Note

The Seller, hereby expressly disclaims all warranties either express or implied, including any implied warranty of merchantability or fitness for a particular purpose, and neither assumes nor authorizes any other person to assume for it any liability in connection with the sale of this part(s) and/or service. Buyer shall not be entitled to recover any consequential damages, damages to property, damages for loss of use, loss of time, loss of profits, or income, or any other incidental damages. In addition, expressly excluded is any liability for defects pertaining to safety or performance, by way of ‘‘strict liability’’, negligence or otherwise. In the event of non-payment, the Buyer agrees that the costs of collection including court cost, and reasonable attorney’s fees, shall be recoverable from the Buyer. The Buyer has read and with any transaction, agrees to all of the terms and conditions in connection with the Seller.


Terms: • All Returns/Exchanges Require Written or Verbal Pre-Authorization and RMA Number. • Positively No Exchanges Without This Invoice. • No Refunds On Opened Packages Or Used Parts. • Items Returned Must Be In Original Packaging. • No Refunds On Special Orders. • No Return On IMS Parts. • No Refunds After 30 Days. • 25% Handling Charge On All Returned Items. • No Returns On Electrical Parts. • Refund On Purchases Paid By Check Are Refunded After Check Clears. • Limited Lifetime Warranty on NSC plating provided by Millennium Technologies LLC and subject to their terms and conditions. • There is no warranty on blocks processed with the Nickies Lite direct plating process. • Any Damage Must Be Reported to the Shipper and LN within 24 Hours of Receipt.

By continuing with your purchase and completing the checkout process you acknowledge and agree with Sales Terms and Conditions.

View also the additional information about Privacy and Security

Questions or comments? Feel free to contact us before ordering. Open a service ticket, call 815.472.2939 or email support@lnengineering.com.