You have no items in your shopping cart.

You have no items to compare.

Head Studs

ARP 204-4707 M96/M97 Head Stud Kit 97-08 Porsche Boxster, Cayman, 911


More info on LN Engineering's Prop 65 policy

ARP 204-4707 M96/M97 Head Stud Kit 97-08 Porsche Boxster, Cayman, 911

$546.99

In stock

SKU: 204-4707

ARP 204-4707 M96/M97 Head Stud Kit 97-08 Porsche Boxster, Cayman, 911

8740 Chromoly ARP Cylinder Head Stud Kit for 2.5, 2.7, 3.2, 3.4, 3.6, and 3.8 engines found in all Boxster, Cayman, and 911 models with the M96/M97 engine.

The factory carrier bolts are torque to yield (TTY) and must be replaced. This ARP kit features bolts that are stronger (and reusable) and an upgrade of the factory stretch bolts for any build.

Installation Method for Porsche Head Stud Kit


Part Number: 204-4707

Application: Porsche 3.4L Non-Turbo Water-Cooled Engine



  1. Always verify the part number for your application with the part number on the side of the box and the part number on the instruction sheet.

  2. Clean and inspect all hardware prior to installation. Look for obvious defects or shipping damages plus proper fit, length, and dimension.

  3. To ensure proper thread engagement and accurate torque readings, clean ALL threads in the block. Chase if necessary with ARP Thread Chaser part number 912-0003 (M10 X 1.5).

  4. Screw the head studs into the left-hand and right-hand engine cases "HAND TIGHT ONLY". NOTE: LOCTITE MAY BE USED IF A PERMANENT MOUNTING OF THE STUDS IS PREFERRED.

  5. Install the cylinder heads as described in the Porsche factory service manual. Check for binding or misalignment.

  6. Lubricate the stud threads, nuts, and washers with ARP ULTRA-TORQUE FASTENER ASSEMBLY LUBRICANT. Then install the washers and the nuts onto the studs and tighten them hand tight. ARP recommends using the ARP ULTRA-TORQUE FASTENER ASSEMBLY LUBRICANT that is provided with each kit as opposed to motor oil. This is due to higher friction on the studs as well as inconsistencies in the clamping force of the fasteners when motor oil or other low-quality lubricants are used.

  7. Following the manufacturer's recommended torque sequence, tighten the nuts in two equal steps to 60 ft-lbs with ARP ULTRA-TORQUE FASTENER ASSEMBLY LUBRICANT. Note: ARP Ultra-Torque Fastener Assembly Lubricant has been specifically designed to reduce tension preload scatter and eliminate the need to cycle high-performance engine fasteners before final installation. ARP Ultra-Torque far surpasses all requirements offered by previous ARP lubricants in terms of fastener preload repeatability and performance lubricating properties.


Description

Details

Cross Reference: 204-4707, 996-104-180-53; 996-104-180-54; 996-104-180-55; 996-104-180-56; 996-104-180-57; 99610418055; 99610418057; 99610418053; 99610418054; 99610418056; 99610418059; 996-104-180-58, 99610418058, 996-104-180-59

Additional

Additional Information

Brand ARP
MPN 99610418059
MSRP No

Important Seller's Note

The Seller, hereby expressly disclaims all warranties either express or implied, including any implied warranty of merchantability or fitness for a particular purpose, and neither assumes nor authorizes any other person to assume for it any liability in connection with the sale of this part(s) and/or service. Buyer shall not be entitled to recover any consequential damages, damages to property, damages for loss of use, loss of time, loss of profits, or income, or any other incidental damages. In addition, expressly excluded is any liability for defects pertaining to safety or performance, by way of ‘‘strict liability’’, negligence or otherwise. In the event of non-payment, the Buyer agrees that the costs of collection including court cost, and reasonable attorney’s fees, shall be recoverable from the Buyer. The Buyer has read and with any transaction, agrees to all of the terms and conditions in connection with the Seller.


Terms: • All Returns/Exchanges Require Written or Verbal Pre-Authorization and RMA Number. • Positively No Exchanges Without This Invoice. • No Refunds On Opened Packages Or Used Parts. • Items Returned Must Be In Original Packaging. • No Refunds On Special Orders. • No Return On IMS Parts. • No Refunds After 30 Days. • 25% Handling Charge On All Returned Items. • No Returns On Electrical Parts. • Refund On Purchases Paid By Check Are Refunded After Check Clears. • Limited Lifetime Warranty on NSC plating provided by Millennium Technologies LLC and subject to their terms and conditions. • There is no warranty on blocks processed with the Nickies Lite direct plating process. • Any Damage Must Be Reported to the Shipper and LN within 24 Hours of Receipt.

By continuing with your purchase and completing the checkout process you acknowledge and agree with Sales Terms and Conditions.

View also the additional information about Privacy and Security

Questions or comments? Feel free to contact us before ordering. Open a support ticket, call 815.472.2939 or email support@lnengineering.com.