Oil Change Bundle for MY 1997 - 2008 Boxster/Cayman/911

RND Engines RS Roller Bearing Kit

RND Roller Bearing IMS Retrofit kit is the only solution on the market that uses proper heat treated, 52100 bearing steel thrust surfaces on both sides and provides true thrust control integral to the bearing.

RS Roller Bearing Kit

Oil Change Bundle for MY 1997 - 2008 Boxster/Cayman/911

As low as: $172.75

Price as configured: $0.00

In stock

Oil Change Bundle for MY 1997 - 2008 Boxster/Cayman/911 is available for purchase in increments of 1

Makes oil changes easy again and save some $ at the same time!

Billet AL Hard Anodized Magnetic Drain Plug. Also fits 09+ 9A1 and 03-06 Cayenne S/Turbo   +$23.82
Spin-on Oil Filter Adapter   +$137.83
Replacement Oil Filter for Spin-On Oil Filter Adapter (Not for IMS Solution)   +$11.10

* Required Fields

Oil Change Bundle for MY 1997 - 2008 Boxster/Cayman/911 is available for purchase in increments of 1



LN Engineering's exclusive full-flow spin-on oil filter adapter allows for use of a conventional spin-on oil filter, rather than expensive and messy cartridge-style filters.

The LN Engineering Spin-On Oil filter adapter also helps improve the longevity of your engine by providing full flow filtration by deleting the bypass, which means 100% of the oil gets filtered and whatever goes to the filter stays in the filter. This limits collateral damage from foreign object debris that would otherwise re-contaminate the engine when using the factory filter arrangement.

Since a steel-bodied spin-on conventional oil filter is now employed, you can further reduce engine wear by using a Filtermag, which reduces iron contaminants in your motor oil and thus reduces wear associated with these particles normally unfiltered by the oil filter.

When installing, be sure to lubricate both o-rings with clean engine oil. Screw the oil filter adapter onto the engine by hand. Once the spin on filter adapter is fully engaged to the block, use a 26mm socket and torque to 25 Nm (18 Ft/Lbs). Also be sure to oil the filter gasket and pre-fill the oil filter before installing! Filter should be installed by hand then once snug, turned another 3/4 to 1 turn to finish filter installation, or to the filter manufacturers recommended specifications. We use the Napa Gold 1042 or Platinum 1042 along with Joe Gibbs DT40 or the LN Engineering Billet Spin-On Oil Filter and Joe Gibbs XP9 for the track. For street use in warmer climates, a 5w40 full-synthetic oil is recommended and for winter use with frequent cold starts, we recommend a 0w40 full-synthetic oil. Porsche approved oils of 0w40 and 5w40 are acceptable - use of thicker oils not recommended. Oil change interval should not exceed 6 months or 5,000 miles in street use. For track use, our Billet High Performance Oil Filter is recommended and required when running an Accusump and is included in HPDE Accusump Kit, part number 106-12.1.

LN Engineering’s billet aluminum hard-anodized magnetic drain plug is CNC machined from 6061-T6 aluminum and has a large 3/8” rare-earth magnet to reduce iron (Fe) levels in oil, which is a primary source for wear in your engine, with up to 14 lbs. of pull! Fits MY09 and later 9A1 DFI engines used in Boxster, Cayman, and 911 models, as well as MY97-08 M96 and M97 engines. Also fits Cayenne S/Turbo MY03-06 models. The addition of a magnetic drain plug allows for quick and easy inspection of overall engine health and for identification of engine problems from foreign object debris collected by our magnet. Our drain plug uses M18x1.5mm thread pitch and replaces the original drain plug, Porsche part no 900 219 009 30, and uses O.E. sealing ring Porsche part number 900 123 106 30 which should be replaced every time you install the drain plug and torqued to 19 ft/lb.

NOTE: Does not work with 911 Turbo/GT2/GT3 engines.


Additional Information

Brand LNE

Important Seller's Note

Products and services provided by Seller have the potential to substantially raise the torque and horsepower output of an engine. Additionally, high performance parts exert greater stress on engine components. Seller assumes no responsibility for injury or damage resulting from increased torque and horsepower output or failure of any components due to Seller's products and services. Seller urges that Seller's products not be used unless, after an engine has been modified with Seller's parts and services, the owner is able to operate safely, and is willing to accept responsibility for the effects Seller's products and services may have.

By continuing with your purchase and completing the checkout process you acknowledge and agree with Sales Terms and Conditions.

View also the additional information about Privacy and Security

Questions or comments? Feel free to contact us before ordering. Open a service ticket, call 815.472.2939 or email