You have no items in your shopping cart.

You have no items to compare.

Piston/Cylinder/Rings

ARP Cylinder Head Stud Kit for Porsche 914 912E VW Type 2/4


More info on LN Engineering's Prop 65 policy

ARP Cylinder Head Stud Kit for Porsche 914 912E VW Type 2/4

$479.00

In stock

SKU: 201-02

LN Engineering exclusive ARP VW Type 2/4 and Porsche 914 912E cylinder head stud kit. Includes 8 short and 8 long studs, 16 nuts and washers, and ARP lube. Designed as a direct replacement for the factory head studs case threads and does not require inserts to be installed in case as is required when using Raceware RWE-1024 head studs.

Upgraded cylinder head studs are required for all Type 4 engine builds utilizing our Nickies cylinders for optimal head and cylinder sealing.

* Required Fields

Description

Details






ARP Cylinder Head Stud Kit for Porsche 914 912E VW Type 2/4


Instructions and Specifications


Instructions


Operations Performed During Shortblock Assembly


  • Remove old cylinder head studs from crankcase.
  • Clean the threads in the case with proper thread chase. There should be no binding of the stud when it is screwed into the case by hand.
  • Install the eight studs that go into blind holes with anti-seize lubricant and the eight studs that go into through holes with a non-curing sealant, such as Hylomar or Curil-T, since it allows repositioning of the cylinder head stud later on if required.

Operations Performed During Longblock Assembly


  • After installing cylinders and heads onto the engine, apply the supplied ARP moly-lube to the fine threads of each stud.
  • Apply non-hardening sealant on both sides of the washer, then install washers and nuts as normal. The nuts fit either a 12-point 7/16” or 12-point 11mm socket. Tighten each nut to a “snug” fit with no preload.
  • Tighten all nuts to 14 ft-lb in the following sequence:
    6 4 2 8
    7 1 3 5
  • Tighten nuts again to 28 ft-lb using the same pattern.
  • Tighten nuts to the final torque spec of 32 ft-lb using the same pattern.
  • Repeat above step to ensure that all nuts received the proper preload.
  • Wipe off excess moly lube on studs.

Operations Performed After Engine Break-In


  • Re-torque cylinder heads after first 100 miles to final 32 ft-lb torque spec.
     

Specifications


Your head studs are designed to the highest standards and manufactured by ARP in the United States. Please note that the threads on the head-side are 3/8”-24 and hardware has a corrosion-resistant black-oxide finish.


Cross Reference: 025101147A, 021101147A, N0215701, N0215741

Additional

Additional Information

Brand ARP
MPN No
MSRP No

Important Seller's Note

The Seller, hereby expressly disclaims all warranties either express or implied, including any implied warranty of merchantability or fitness for a particular purpose, and neither assumes nor authorizes any other person to assume for it any liability in connection with the sale of this part(s) and/or service. Buyer shall not be entitled to recover any consequential damages, damages to property, damages for loss of use, loss of time, loss of profits, or income, or any other incidental damages. In addition, expressly excluded is any liability for defects pertaining to safety or performance, by way of ‘‘strict liability’’, negligence or otherwise. In the event of non-payment, the Buyer agrees that the costs of collection including court cost, and reasonable attorney’s fees, shall be recoverable from the Buyer. The Buyer has read and with any transaction, agrees to all of the terms and conditions in connection with the Seller.


Terms: • All Returns/Exchanges Require Written or Verbal Pre-Authorization and RMA Number. • Positively No Exchanges Without This Invoice. • No Refunds On Opened Packages Or Used Parts. • Items Returned Must Be In Original Packaging. • No Refunds On Special Orders. • No Return On IMS Parts. • No Refunds After 30 Days. • 25% Handling Charge On All Returned Items. • No Returns On Electrical Parts. • Refund On Purchases Paid By Check Are Refunded After Check Clears. • Limited Lifetime Warranty on NSC plating provided by Millennium Technologies LLC and subject to their terms and conditions. • There is no warranty on blocks processed with the Nickies Lite direct plating process. • Any Damage Must Be Reported to the Shipper and LN within 24 Hours of Receipt.

By continuing with your purchase and completing the checkout process you acknowledge and agree with Sales Terms and Conditions.

View also the additional information about Privacy and Security

Questions or comments? Feel free to contact us before ordering. Open a support ticket, call 815.472.2939 or email support@lnengineering.com.