Victor Reinz REINZOSIL Sealing Compound 70mL Tube 70-31414-10
sku: 16005

Victor Reinz REINZOSIL Sealing Compound 70mL Tube 70-31414-10

$11.50

Material: Anthracite colored, solvent-free sealing, adhesive & coating compound based on silicone. Once completely bonded, REINZOSIL is virtually odorless.

Properties: This highly elastic universal sealing compound (silicon sealant) is resistant to mineral oils and numerous synthetic oils, lubricants, petrol, diesel oil, greases, hot and cold water, detergents, sunlight, ozone, and sea water. REINZOSIL is suitable for continuous operation in the temperature range between -50 °C and +250 °C (briefly up to 300 °C). Hardness (softness) lies in the range of 30 to 35 Shore A. Application Due to its special properties, REINZOSIL is used in the most varied applications, e.g. as FIPG (formed-in-place gasket) for wet assembly, i.e. for sealing small gaps under pressure as well as for cylinder liners in piston machines, and also to compensate for extensive component warping. Moreover, the compound is also used to seal constructional fissures or cracks, and for seals that are subjected to considerable relative movement. The compound can also be applied to assembled components. In these cases, after the sealing joint has been cleaned and degreased, REINZOSIL is applied directly to the sealing gap, similar to the procedures used in the building industry.

Instructions for use: Remove any gasket remnants or other residues such as grease, oil, etc. with RE-MOVE solvent remover. Allow the surfaces to dry, then apply the sealing compound on one side manually or by means of a pneumatic spraying device. Assemble the components immediately. Processing temperature lies between +5 °C and +40 °C. Depending on temperature and humidity, a skin develops after 5 to 12 minutes. The full curing time depends mainly on the relative air humidity (RH) and room temperature, as well as on the thickness (gap height) and width of the applied layer.

Please note: The higher that air humidity and temperature are, or the thinner and narrower the sealing layer is, the shorter will the curing time be. With a layer or gap width of e.g. 7 mm, and a thickness or gap height of 1,5 mm at 40 °C and 90 % RH, the full curing time is about 9 hours, provided that temperature and humidity have access to both sides. With the above sealing gap dimensions, but at normal ambient conditions (approx. 23 °C and 50 % RH), curing time would be about 100 hours. Fully cured (vulcanized) material can only be removed mechanically.

Caution! Irritation of the respiratory tracts! Ensure good room ventilation.

Storage period: Unopened cartridges can be stored for about 12 months in a dry environment (+5 °C up to 25 °C).

in , Brand:

Description

Cross Reference: 70-31414-10, 703141410, 70 31414 10, 70.31414.10, 55-9526-008, 55 9526 008, 559526008, 55.9526.008

Important: Before ordering, always confirm that the part fits your specific type/model/engine.

Additional information

Weight 1 lbs
  • Images are stock photos. Actual product may vary. While we strive to ensure that all product images and descriptions on our website are accurate, slight variations in appearance may occur due to updates in design, manufacturing processes, or material finishes. These differences do not affect the functionality or quality of the product. If you have specific concerns or need more details before purchasing, please contact our customer support team for assistance.
  • Some items may be special order, out of stock, subject to additional freight charges, or import duties. Customers will be contacted for any of these special situations for customer approval before proceeding with any order.
  • The Seller, hereby expressly disclaims all warranties either express or implied, including any implied warranty of merchantability or fitness for a particular purpose, and neither assumes nor authorizes any other person to assume for it any liability in connection with the sale of this part(s) and/or service. Buyer shall not be entitled to recover any consequential damages, damages to property, damages for loss of use, loss of time, loss of profits, or income, or any other incidental damages. In addition, expressly excluded is any liability for defects pertaining to safety or performance, by way of ‘‘strict liability’’, negligence or otherwise. In the event of non-payment, the Buyer agrees that the costs of collection including court cost, and reasonable attorney’s fees, shall be recoverable from the Buyer. The Buyer has read and with any transaction, agrees to all of the terms and conditions in connection with the Seller.
  • Terms: • All Returns/Exchanges Require Written or Verbal Pre-Authorization and RMA Number. • Positively No Exchanges Without This Invoice. • No Refunds On Opened Packages Or Used Parts. • Items Returned Must Be In Original Packaging. • No Refunds On Special Orders. • No Return On IMS Parts. • No Refunds After 30 Days. • 25% Handling Charge On All Returned Items. • No Returns On Electrical Parts. • Refund On Purchases Paid By Check Are Refunded After Check Clears. • Limited Lifetime Warranty on NSC plating provided by Millennium Technologies LLC and subject to their terms and conditions. • There is no warranty on blocks processed with the Nickies Lite direct plating process. • Any Damage Must Be Reported to the Shipper and LN within 24 Hours of Receipt.

Some products sold by LN Engineering LLC or on https://www.LNengineering.com contain or may contain chemicals known to the State of California to cause cancer, birth defects or other reproductive harm. LN Engineering has chosen to provide a warning based on its knowledge of the presence of one or more listed chemicals without evaluating the exposure. Products may contain chemicals in amounts acceptable by the safe harbor levels as outlined by Proposition 65, or not at all, however we have chosen to issue this warning on all of our products as an act of caution.

You may also like…

Related products